• 086D20
  • Short-sledge Impulse Hammer w/force sensor & tips, 0 to 5k lbf, 1 mV/lbf (0.23 mV/N)

    Sensitivity: (±15%) 1 mV/lbf (0.23 mV/N)
    Measurement Range: ±5000 lbf pk (±22240 N pk)
    Hammer Mass: 2.4 lb (1.1 kg)
  • 086E80
  • Miniature Instrumented Impulse Hammer, 0 to 50 lbf

    Sensitivity: (±20%) 100 mV/lbf (22.5 mV/N)
    Measurement Range: 50 lbf pk (222 N pk)
    Hammer Mass: 0.17 oz (4.8 gm)
  • 130E20
  • ICP? microphone with integral preamplifier, BNC jack connector

    Nominal Microphone Diameter: 1/4\"
    Frequency Response Characteristic: Free-Field
    Electrical Connector: BNC Jack
  • 377B02
  • 1/2\" free-field, prepolarized condenser microphone, typical sensitivity= 50 mV/Pa (+/-1.5 dB), 3.15 Hz to 20 kHz (+/-2 dB).

    Nominal Microphone Diameter: 1/2\"
    Polarization Voltage: 0 V
  • 378B02
  • 1/2\" prepolarized free-field condenser microphone, 50 mV/Pa (+/-1.5 dB), 3.15 Hz - 20 kHz (+/-2 dB) with 1/2\" ICP? preamplifier (426E01) and TEDS
    This model includes a 1/2\" microphone cartridge, a mated preamplifier with TEDS, and system calibration. Click the following for individual component information.
  • 393B04
  • Seismic, miniature (50 gm), ceramic flexural ICP? accelerometer, 1 V/g, 0.06 to 450 Hz, 10-32 top connector

    Sensitivity: (±10%) 1000 mV/g (102 mV/(m/s²))
    Broadband Resolution: 0.000003 g rms (0.00003 m/s² rms)
    Measurement Range: ±5 g pk (±49 m/s² pk)
    Frequency Range: (±5%) 0.06 to 450 Hz
    Electrical Connector: 10-32 Coaxial Jack
  • 394C06
  • Handheld shaker, 1g at 159.2 Hz (for up to 210 grams total weight of sensor, cable and mounting accessories).

    Acceleration Output: (±3%) 1.00 g rms (9.81 m/s² rms)
    Velocity Output: 0.39 in/sec rms (9.81 mm/s rms)
    Operating Frequency: (±1%) 159.2 Hz
    Maximum Load: 7.4 oz (210 gm)
    Weight: 31 oz (900 gm)
  • 478A01
  • 1-channel, battery-powered, signal cond. for single-ended MEMS and capacitive sensors with 4-pin input connector
    Battery-powered, unity gain signal conditioner for capacitive sensors and single-ended MEMS DC sensors. 4-pin input connector, BNC output connector, and DC offset null adjustment.
  • 480B21
  • 3-channel, battery-powered, ICP? sensor signal cond., gain x1, x10, x100, BNC input/output connector
    3-channel, Battery-powered, ICP? Sensor Signal Conditioner with Gain x1, x10 and x100 for each channel. BNC input and output connectors. Uses three 9-volt alkaline batteries (included).
    Channels: 3
  • 480C02
  • Platinum Stock Products; 1-channel, battery-powered, ICP? sensor signal cond., unity gain, BNC input/output connector
   81  82  83  84  85  86  87  88  89  90